Features

Design benefits

waterproof

Moderate rain for 2 hrs 5,000 mm Schmerber (JIS standard) Pockets not waterproof

breathability

Very breathable coated fabric (RET < 12): reduces condensation

pockets

3 secure pockets, including 1 inner pocket

windproof

Fabric especially coated to reduce the cooling effect of the wind.

Design details

Waterproofing 1/2

We measure the resistance of a fabric to water pressure in mm of water column (based on ISO 811 ). The higher the water pressure withstood by the fabric, the more waterproof it is. Here are the waterproofing ratings: Component resistant to water pressure of 5,000 mm before and after ageing (5 washes). This equates to 5,000 Schmerber - average pressure exerted by the water during rain. The anorak's waterproofness was tested in a rain shower with 60 litres of water/m²/hour for 2 hours.

Waterproofing 2/2

- High collar - Injection-moulded plastic to avoid salt oxidation - Water-repellent components (water runs off the fabric) - 100% taped seams - Central opening features a flap with a drainage channel for optimal waterproofing

Hood

The hood does not pack down into the collar, it is attached. Completely depth and height-adjustable hood. Visor with a headband to provide a good level of protection and a better hold. The high neck effectively protects the neck.

pockets

2 zip pockets on the front of the jacket to put your hands or some items 1 inside pocket on the right side of the chest with a rip-tab closing NOTE: the pockets are NOT WATERPROOF

Front zip closure

A zip on the entire jacket length with an interior flap protects against the wind and water. Soft fabric flap on the top of the collar to protect the chin.

Fabric breathability

To find out whether a fabric is breathable, we test its evaporate resistance or RET (ISO 11092 standard). The lower the fabric's resistance, the more moisture is evaporated, and therefore the higher the fabric's breathability. We consider that if: RET < 9 = very breathable fabric 9 < RET < 12 = breathable fabric. The values for the Trek 500 jacket’s breathability are as follows: > More resistant fabric: RET < 12 (or 3621 g/m²/24 h, JIS1099A standard) > Lightest fabric: RET < 8 (or 2972 g/m² /2

Water-repellent properties information

A fabric is water-repellent when water slides off the surface of the fabric, without seeping in. Your jacket does not become waterlogged and remains lightweight and breathable. The water-repellent properties are achieved with a treatment applied to the external side of the fabric, but in practice these properties can be altered. The water-repellent properties can be reactivated by putting the jacket in a dryer for 10 minutes at the lowest temperature.

How to wash your jacket?

To maintain the water repellent properties, infrequent washing is recommended. Close all zips and flaps, empty all pockets and then turn the garment inside out to wash it. You can wash it on a synthetic cycle at 30°C or 40°C with your usual detergent. Do not use fabric conditioner, which could damage the existing performance of the garment, or bleach. Very important: choose a full rinse cycle or extra rinse.

How to reactivate the jacket's water repellency

Drying is a crucial phase in reactivating the water repellent treatment. We recommend that you lay your jacket flat on a clothes rack and leave it out to dry in the open. Caution: never dry your jacket directly on a radiator. Then place them in the tumble dryer on a short synthetics cycle, i.e. 10 to 15 minutes, before turning it back the right way round. Caution: do not over-dry the garment.

frequency	occasional
weather conditions	rainy weather
rain	moderate rain
fit	fitted
neck type	zip neck
type of opening/closing	zip
number of pockets	3 pockets
reversible	not reversible
zip type	full zip
type of lining	light/no lining
snow skirt	without snow skirt
waterproof	waterproof
hood	with hood
pocket	inside pocket, zip closed pocket, with pocket
main material	polyester
style	plain
membrane construction	2 layers
ventilation system	without ventilation
mm H2O (Schmerbers)	5,000 mm
type of length	at the hips
condition	new
windproof	windproof
lining material	synthetic
sleeves length	long sleeves
modular	not modular
stitching type	with seam
reflective	without reflective zones
type of waterproofing	coating
thumb pass	without thumb pass
type of hood	adjustable hood, hood with visor
breathability (in RET)	RET 6 < RET < 12 : moderately breathable
storage	without storage

Raw material	85.505%
Manufacturing	3.61%
Packaging	0.916%
Distribution	5.658%
Use	3.502%
End of life	0.808%

Women's sailing waterproof jacket - Wet-weather jacket SAILING 100 navy blue

Features

Design benefits

Design details

Specifications

Details

Composition

Usage & care

Care instructions

Cleaning

Environmental impact

Carbon footprint

Ecodesign approach